Cleaning stains, sweat, and filth from clothing is easy with a washing machine. But it is quite unacceptable if you lift the lid after the washer has stopped running and discover your garments are swimming in water.
Not draining or spinning are one of the common problems of a washing machine.
Whirlpool washer not draining or spinning
One of the most frequent reasons for a Whirlpool washer not draining is a crooked or clogged drain hose. If your Whirlpool washer will not drain, the problem is probably with the lid switch, door lock, drain pump, or drain line. The control panel or timer could also be an issue.
Your whirlpool washer might not be draining or spinning for various reasons. Let’s talk about these in details –
Not draining
Front-load
The Cycle you have chosen is important:
The improper setting for your specific load will result in wet garments after the wash cycle has finished.
Solution:
Before turning on your washer, double-check the settings and clothing tags to be sure you’ve chosen the appropriate cycle for your load.
Different Spin can react differently:
The highest spin speed recommended for the kind of wash load you are cleaning is what you should choose. By doing this, you may get rid of the most water without harming your garments.
Solution:
The control adjacent to your programmer dial on the front of your machine can be used to change the spin speeds. Always choose a spin speed because your garments won’t dry after the cycle is over.
Pushing a bulky item in the washer causes problem:
When washing oversized goods like blankets or carpets, things that collect on one side of the washer drum can restrict its motion. Additionally, they may slow down the spin cycle’s pace and draining.
Solution:
Run a second spin cycle after redistributing the material more evenly in the washer drum.
Highly Efficient or Excessive Detergent has some adverse impact:
Excessive suds can be produced by using non-HE detergent or using more detergent than what the manufacturer suggests, and it may cause the washer to run at a lower spin speed, producing loads that are very wet.
Solution:
Use HE High Efficiency detergent only.
Top-load
The Draining Hose May be Clogged or Kinked:
If the washer moves or pushes the hose up against the wall, kinks may develop. Water backs up inside the washer because of the hose’s twist restricting water flow.
Solution:
Firstly, straighten the hose. Clear any obstruction in the drainpipe.
See if the Draining Hose is above the floor:
If the drainpipe is longer than 96″, your washer won’t be able to pump the water out of the washer. In this situation, the water might return to the washer.
Solution:
The drain hose’s height shouldn’t be more than 96 inches.
A huge amount of Load at once is not suitable:
Wet garments at the end of the cycle and lower spin speed can result from large or imbalanced loads.
Solution:
The laundry load must be evenly distributed and not overly crowded.
What is your preferred cycle or spin speed?
Depending on the material being washed, the washer’s spin speed may change.
Solution:
Wool, and blouses need a lower spin speed while cotton benefits from a higher speed.
Not spinning
Front-load
The Rotor Belt is Worn out:
Your washing machine will drain but not spin, or it will spin in an inconsistent manner, if this thin rubber belt snaps or becomes slack on the pulleys.
Solution:
Drive belt repair is necessary if it has become loose and stretched or has cracks or tears.
Faulty Washer Door Lock:
It will not tell the washer to start a wash cycle and spin if the door lock is faulty.
Solution:
When closing the washer door, listen for an audible sound if Whirlpool washer is not spinning. Check the lock for obvious damage or perform a multimeter test if it does not produce this noise when the door closes.
The lock components need to be replaced if they are broken or do not test positive with a multimeter.
Washer Tub Bearing Failure:
The washer’s outer tub contains the tub bearing, allowing the inner tub to spin easily. Your Whirlpool front-load washer will not spin even though it is functioning loudly if it wears out or breaks.
Solution:
A professional repair service should handle the difficult repair of a failing tub bearing.
Top-load
Lid switch Malfunction:
The lid switch’s job is to turn off your washer when the lid is improperly closed. Your washer will stop spinning if it accidentally switches off the power.
Solution:
First, ensure that the washer’s power is turned off. Track down the lid switch. Once found, you must remove the lid switch and use a multimeter to make sure it is working.
If there is no continuity in the lid switch, it is broken and needs to be replaced.
Motor Coupling is Damaged:
The washer motor is coupled to the transmission by the coupling. The connection aids in defending the transmission and motor from damage if your washer is overloaded.
Solution:
Locate the motor coupling location. You will need to remove the washer’s top and side panels to access it. If motor coupling is damaged, it must be replaced.
Door Latch:
A washer’s door stays closed while a cycle is in progress thanks to the door latch. Your washer won’t start spinning if the door is not firmly closed when you turn it on and opens throughout the cycle.
Solution:
To determine whether your washer has a mechanical or electronic door lock, see your manual.
If your washer has a mechanical door latch, the door will need to be replaced if it won’t close securely. If it is electrical, the door latch will need to be replaced if it lacks consistency by using a multimeter.
Stator Assembly:
Your Whirlpool washer’s inability to spin has yet another potential cause: a bad stator assembly.
Solution:
To inspect the stator assembly at first, find the stator. Look for any signs of damage in the stator’s windings. The stator should be changed if they are damaged.
Is whirlpool washer not draining a common issue?
Any washer can stop draining for various reasons. Let’s find out below if this is a common problem for whirlpool washers –
Whirlpool cabrio washer:
The most common causes of a washer that will not drain is a broken drain pump or a clogged drain hose.
A foreign object or small piece of clothing that has slipped past the washer’s filters and is obstructing the pump could be the root of the problem. The impellers of the drain pump may also be broken, causing the pump to run slowly.
Electricity failures might affect the drain pump. Sometimes a broken lid switch will stop the washer from draining.
Whirlpool duet washer:
The drain hose or drain pump is typically to blame if Whirlpool Duet washer will not drain. Make sure the proper spin setting and detergent is used. Large, bulky laundry can also slow down the spin cycle, leaving water in the tub after the wash.
Check to see if there are any obstructions in the drain hose. The drain hose should also be placed according to the manufacturer’s instructions, not too low or high.
A multimeter can be used to evaluate the drain pump to see if it has electrically failed.
How do I reset my Whirlpool washer that won’t spin and drain?
You can reset your Whirlpool washer that won’t spin and drain by following few easy steps that are given below –
Unplug Your Whirlpool Washer:
The washer can reset by allowing the electrical charge to leave it after performing the reset. If the reset does not work, try again, but this time wait twice as long.
See if the Circuit Breaker is Okay:
Make sure the circuit breaker is working fine. By turning off the circuit breaker and waiting for 30 seconds, the washer can also be reset.
Then Press Some Buttons:
Some buttons must be pressed and the way to learn which buttons to press to reset the washer is to locate its handbook. Pressing the Pause/Cancel and Power buttons together may also work.
If there is a dial, then turn it:
If there is a dial, turn the setting to “Normal.” Use one press of counterclockwise rotation on the dial, then three clockwise presses, one press of counterclockwise rotation, and one clockwise press. Select Start from the menu.
Check to see if the Stop, Wash, and Rinse buttons are lit up.
Plug the Whirlpool Washer and Turn it on:
Shut off the washer’s power for 20 seconds then activate it, which will now be reset.
Final Thoughts
If the washer will not drain or spin, either the pump is faulty, or something is blocked in the drain hose or pump. Other sources of problem include faulty door lock, drain pump, drain line, or lid switch. Timer or control panel could also be defective.